Bk-precision 4079 - Manual Manuel d'utilisateur Page 11
- Page / 106
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
5
Section 2
Installation
2.1 Introduction
This section contains installation information, power requirements, initial inspection and signal connections for Model 4076
and 4079.
2.2 Mechanical Inspection
This instrument was carefully inspected before shipment. Upon receipt inspect the instrument for damage that might have
occurred in transit. If there is damage due to shipping, file a claim with the carrier who transported the unit. The shipping and
packing material should be saved if reshipment is required. If the original container is not to be used, then use a heavy carton
box. Wrap the unit with plastic and place cardboard strips across the face for protection. Use packing material around all sides
of the container and seal it with tape bands. Mark the box "FRAGILE".
2.3 Initial Inspection
After the mechanical inspection, verify the contents of the shipment (accessories). If the contents are incomplete, or if the
instrument does not pass the specification acceptance tests, notify the local service center.
2.4 Instrument Mounting
The Model 4076 and 4079 - Function Generators are intended for bench use. The instrument includes a front feet tilt
mechanism for optimum panel viewing angle. The instrument does not require special cooling when operated within
conventional temperature limits. The unit can be installed in a closed rack or test station if proper air flow is assured for
removing about 20 W of power dissipation.
2.5 Product Dimensions
300 mm
213 mm
88 mm
- Safety Summary 3
- Table of Contents 5
- Section 1 7
- Specifications 8
- Modulation Combinations 10
- Section 2 11
- 2.8 Signal Connections 12
- 2.9 RS-232 Connection 12
- 2.6 Power Requirements 12
- 2.7 Grounding Requirements 12
- 2.10 RS-232 Configuration 13
- 2.11 GPIB Address 14
- 2.12 GPIB Connections 14
- Section 3 15
- 3.2 Display Window 16
- 3.3 Front Panel Controls 17
- 3.4 Back Panel Controls 17
- 18
- Model 4076 18
- Model 4079 18
- 3.5 Output connectors 19
- 3.6 MENU Keys 19
- 3.6.1 PARAMETER Key 22
- 3.6.2 MODE Key 23
- 3.6.3 WAVEFORM Key 24
- 3.6.4 Arbitrary EDIT Menu 26
- 3.6.5 PULSE Menu 29
- 3.6.6 UTILITY Key 29
- 3.6.7 SWEEP Key 30
- 3.6.8 MODULATION Key 31
- 3.6.9 SETUPS Key 32
- 4,000,000 33
- 3.7 ON Key 34
- 3.8 Cursor Movement Keys 34
- 3.9 Rotary Input Knob 34
- 3.10 Power-On Settings 34
- 3.11 Memory 35
- 3.12 Displaying Errors 35
- 3.13.3 Setting the Output 36
- 3.14 Examples 37
- 3.14.8 Using Voltage Offset 41
- 4.1 Overview 43
- 4.2 Device State 44
- 4.4 Device Address 45
- 4.6 Block Data (GPIB Only) 46
- 4.8 Instrument Reset 46
- 4.9 Self Test 46
- 4.10 Command Syntax 46
- 4.11 Status Reporting 50
- 4.11.4 The Error Queue 51
- 4.11.5 Error Codes 51
- 4.12 Common Commands 54
- 4.13.1 SOURce Subsystem 58
- 4.13.1.2 Amplitude 60
- 4.13.1.3 Offset 60
- 4.13.1.5 Function 61
- 4.13.1.6 Point Rate 62
- 4.13.1.7 AM modulation 62
- 4.13.1.8 FM modulation 63
- 4.13.1.9 FSK modulation 65
- 4.13.1.10 Sweep control 67
- 4.13.1.11 PHASe adjust 68
- 4.13.1.12 PULSe setting 68
- 4.13.1.13 Duty Cycle 70
- 4.13.2 OUTPut Subsystem 70
- 4.13.2.1 Output State 71
- 4.13.2.2 Output Summing 71
- 4.13.3 Trigger Subsystem 71
- 4.13.3.1 Trigger Mode 71
- 4.13.3.2 Trigger Source 72
- 4.13.3.3 Burst Count 72
- 4.13.4 Arbitrary Subsystem 73
- 4.13.4.1 Point Rate 74
- 4.13.4.2 Address 74
- 4.13.4.3 Data 75
- 4.13.4.4 Line Draw 75
- 4.13.4.5 Clear 76
- 4.13.4.6 Copy 76
- 4.13.4.10 Start Address 78
- 4.13.4.11 Wavelength 79
- 4.13.4.12 Marker Address 79
- 4.13.4.13 Marker Length 79
- 4.13.4.14 Marker State 80
- 4.13.4.15 Save 80
- 4.13.5 Status Subsystem 80
- 4.13.5.1 Status Preset 81
- 4.13.5.2 Error Queue Read 81
- 4.13.5.3 Error Queue Enable 81
- 4.13.6 System Subsystem 84
- 4.13.6.3 SCPI Version 84
- 4.13.6.4 Security 85
- 4.13.6.5 Power-on Buffer 85
- 4.14.2 DCL - Device Clear 86
- 4.14.4 LLO - Local Lockout 86
- 4.15 SCPI Command Tree 87
- 4.15.3 :OUTPut Subsystem 88
- 4.15.4 :TRIGger Subsystem 88
- 4.15.5 :ARBitrary Subsystem 88
- 4.15.6 :STATus Subsystem 89
- 4.15.7 :SYSTem Subsystem 89
- 4.17.1 General 93
- Section 5 97
- 5.3 Performance Tests 98
- 5.3.3 Offset Accuracy 100
- 5.3.4 Sine Distortion 100
- 5.3.7 Operating Modes 101
- 5.3.10 GPIB Capability 103
- Performance Tests Results 104
Produits connexes et manuels pour Générateurs Bk-precision 4079 - Manual
(1 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.323 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels