Bk-precision 4079 - Manual Manuel d'utilisateur Page 60
- Page / 106
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
54
Units specifying Arbitrary Point Rate or Wavelength, since the MAXimum or MINimum value is calculated at the
time the command is parsed.
2) The MIN and MAX arguments refer to currently settable minimum or maximum.
3) FIXed is alias for CW.
4.13.1.2 Amplitude
:SOURce:VOLTage[:AMPLitude] <p-p amplitude>
The amplitude command is used to set the peak-to-peak amplitude of the output waveform. Note that the amplitude and the
offset are limited by the relation
Peak Amplitude + |Offset| ≤ 5V
Arguments
Type: Numeric
Units: V, mV,
VPP, mVPP
Range: 10mV to 10V
Rounding: 1mV from 10mV to 999mV. 10mV from 1V to 10V.
Command Type: Setting or Query
Setting
Syntax: [:SOURce]:VOLTage:AMPLitude<ws><amplitude>[units]
[:SOURce]:VOLTage:AMPLitude<ws>MINimum|MAXimum
Examples: :VOLT:AMPL 2.5
:VOLT:AMPL 2.5V
:VOLT:AMPL MAX
Query
Syntax: [:SOURce]:VOLTage:AMPLitude?
[<ws>MINimum|MAXimum]
Examples: :VOLT:AMPL?
:VOLT:AMPL? MAX
Response: NR2
Considerations:
1) The MAXimum amplitude is dependent on the offset.
2) The MAX and MIN arguments should not be used in a program message containing an OFFSet command, since
these values are evaluated during parsing, based on the current value of the offset.
4.13.1.3 Offset
:SOURce:VOLTage:OFFSet <offset>
The offset command is used to set the DC offset of the output waveform. Note that the amplitude and the offset are limited by
the relation
Peak Amplitude + |Offset| ≤ 5V
Arguments
Type: Numeric
Units: V, mV
Range: 10mV to 4.99V
Rounding: to 10mV
Command Type: Setting or Query
Setting
Syntax: [:SOURce]:VOLTage:OFFSet<ws><offset>[units]
[:SOURce]:VOLTage:OFFSet<ws>MINimum|MAXimum
Examples: :VOLT:OFFS 2.5
- Safety Summary 3
- Table of Contents 5
- Section 1 7
- Specifications 8
- Modulation Combinations 10
- Section 2 11
- 2.8 Signal Connections 12
- 2.9 RS-232 Connection 12
- 2.6 Power Requirements 12
- 2.7 Grounding Requirements 12
- 2.10 RS-232 Configuration 13
- 2.11 GPIB Address 14
- 2.12 GPIB Connections 14
- Section 3 15
- 3.2 Display Window 16
- 3.3 Front Panel Controls 17
- 3.4 Back Panel Controls 17
- 18
- Model 4076 18
- Model 4079 18
- 3.5 Output connectors 19
- 3.6 MENU Keys 19
- 3.6.1 PARAMETER Key 22
- 3.6.2 MODE Key 23
- 3.6.3 WAVEFORM Key 24
- 3.6.4 Arbitrary EDIT Menu 26
- 3.6.5 PULSE Menu 29
- 3.6.6 UTILITY Key 29
- 3.6.7 SWEEP Key 30
- 3.6.8 MODULATION Key 31
- 3.6.9 SETUPS Key 32
- 4,000,000 33
- 3.7 ON Key 34
- 3.8 Cursor Movement Keys 34
- 3.9 Rotary Input Knob 34
- 3.10 Power-On Settings 34
- 3.11 Memory 35
- 3.12 Displaying Errors 35
- 3.13.3 Setting the Output 36
- 3.14 Examples 37
- 3.14.8 Using Voltage Offset 41
- 4.1 Overview 43
- 4.2 Device State 44
- 4.4 Device Address 45
- 4.6 Block Data (GPIB Only) 46
- 4.8 Instrument Reset 46
- 4.9 Self Test 46
- 4.10 Command Syntax 46
- 4.11 Status Reporting 50
- 4.11.4 The Error Queue 51
- 4.11.5 Error Codes 51
- 4.12 Common Commands 54
- 4.13.1 SOURce Subsystem 58
- 4.13.1.2 Amplitude 60
- 4.13.1.3 Offset 60
- 4.13.1.5 Function 61
- 4.13.1.6 Point Rate 62
- 4.13.1.7 AM modulation 62
- 4.13.1.8 FM modulation 63
- 4.13.1.9 FSK modulation 65
- 4.13.1.10 Sweep control 67
- 4.13.1.11 PHASe adjust 68
- 4.13.1.12 PULSe setting 68
- 4.13.1.13 Duty Cycle 70
- 4.13.2 OUTPut Subsystem 70
- 4.13.2.1 Output State 71
- 4.13.2.2 Output Summing 71
- 4.13.3 Trigger Subsystem 71
- 4.13.3.1 Trigger Mode 71
- 4.13.3.2 Trigger Source 72
- 4.13.3.3 Burst Count 72
- 4.13.4 Arbitrary Subsystem 73
- 4.13.4.1 Point Rate 74
- 4.13.4.2 Address 74
- 4.13.4.3 Data 75
- 4.13.4.4 Line Draw 75
- 4.13.4.5 Clear 76
- 4.13.4.6 Copy 76
- 4.13.4.10 Start Address 78
- 4.13.4.11 Wavelength 79
- 4.13.4.12 Marker Address 79
- 4.13.4.13 Marker Length 79
- 4.13.4.14 Marker State 80
- 4.13.4.15 Save 80
- 4.13.5 Status Subsystem 80
- 4.13.5.1 Status Preset 81
- 4.13.5.2 Error Queue Read 81
- 4.13.5.3 Error Queue Enable 81
- 4.13.6 System Subsystem 84
- 4.13.6.3 SCPI Version 84
- 4.13.6.4 Security 85
- 4.13.6.5 Power-on Buffer 85
- 4.14.2 DCL - Device Clear 86
- 4.14.4 LLO - Local Lockout 86
- 4.15 SCPI Command Tree 87
- 4.15.3 :OUTPut Subsystem 88
- 4.15.4 :TRIGger Subsystem 88
- 4.15.5 :ARBitrary Subsystem 88
- 4.15.6 :STATus Subsystem 89
- 4.15.7 :SYSTem Subsystem 89
- 4.17.1 General 93
- Section 5 97
- 5.3 Performance Tests 98
- 5.3.3 Offset Accuracy 100
- 5.3.4 Sine Distortion 100
- 5.3.7 Operating Modes 101
- 5.3.10 GPIB Capability 103
- Performance Tests Results 104
Produits connexes et manuels pour Générateurs Bk-precision 4079 - Manual
(1 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.694 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels